manualshive.com logo in svg

Telit Wireless Solutions LE910C series, At Commands Reference Manual

Share
Download
Page 1154
Telit Wireless Solutions LE910C series At Commands Reference Manual Download Page 1154

                

LE910Cx AT Commands Reference Guide

 

 

 
80502ST10950A Rev. 14 

Page 1154 of 1904 

2022-03-04 

 

Not  Subject to NDA 

 

 

 

Values: 

0  :  disable the antenna detection URC 

1  :  enable the antenna detection URC 

 

<interval>  integer 

120 

interval between two consecutive 
antenna detection algorithm runs. It is 
expressed in seconds, and has meaning 
only if <mod>=1. 

 

Value: 

1÷3600  :  seconds 

 

<detGPIO>  integer 

0 

defines which GPIO pin is used by the 
antenna detection algorithm as input. 
The chosen GPIO must be configured in 
alternate function, refer to #GPIO 
command. 

 

Values: 

0 

:  no GPIO pin is used 

1÷max  :  max value depends on the module hardware 

 

<repGPIO>  integer 

0 

defines which GPIO pin is used by the 
antenna detection algorithm (as output) 
to report antenna status. It has meaning 
only if <mod>=1. 
The chosen GPIO must be configured in 
alternate function, refer to #GPIO 
command. 
Value 0 means that no report is made 
using GPIO (default 0). 

 

Values: 

0 

:  no GPIO is used 

1÷max  :  max value depends on the module hardware 

 

Summary of Contents for LE910C series

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands