manualshive.com logo in svg

Telit Wireless Solutions LE910C series, At Commands Reference Manual

Share
Download
Page 1086
Telit Wireless Solutions LE910C series At Commands Reference Manual Download Page 1086

                

LE910Cx AT Commands Reference Guide

 

 

 
80502ST10950A Rev. 14 

Page 1086 of 1904 

2022-03-04 

 

Not  Subject to NDA 

 

1  :  GPIO and serial pins are set in input 

with pull down 

 

<DTRWakeUpEn> 

integer 

0 

select the DTR 
behavior 

 

Values: 

0  :  DTR has no effect on module turned 

OFF by #SYSHALT 

1  :  DTR transition from low to high 

turns on again the module turned off 
by #SYSHALT command 

 

<RebootEn> 

integer 

1 

select how the 
module exits 
SYSHALT 

 

Values: 

0  :  module exits from SYSHALT and 

stays in detached mode like CFUN=4 
status. To restore normal behavior, 
the user shall set CFUN=1 

1  :  module exits from SYSHALT 

performing a total reboot 

 

 

 

 

The parameters are not settable. 

 

  AT#SYSHALT=? 

Test command reports the range for the parameters <GPIORestore>, 
<DTRWakeUpEn> and <RebootEn>. 

 

Summary of Contents for LE910C series

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands