Telit Wireless Solutions LE910C series At Commands Reference Manual Download Page 460

Page: 460 / 1904

Page 460

LE910Cx AT Commands Reference Guide

80502ST10950A Rev. 14

Page 460 of 1904

2022-03-04

Not Subject to NDA

+CESQ: 99,99,255,255,<rsrq>,<rsrp>

Name

Type

Default

Description

<rxlev> integer

N/A

received signal strength level, see
3GPP TS 45.008 subclause 8.1.4.

Values:

0 : rssi < -110 dBm

1 : -110 dBm

≤

rssi < -109 dBm

2 : -109 dBm

≤

rssi < -108 dBm

... : ...

61 : - 50 dBm

≤

rssi < - 49 dBm

62 : - 49 dBm

≤

rssi < -48 dBm

63 : - 48 dBm

≤

rssi

99 : not known or not detectable or if the current

serving cell is not a GERAN cell

<ber> integer

N/A

channel bit error rate.

Values:

0÷7 : as RXQUAL values, see 3GPP TS 45.008

subclause 8.2.4

99 : not known or not detectable or if the current

serving cell is not a GERAN cell

<rscp> integer

N/A

received signal code power (see
3GPP TS 25.133 subclause 9.1.1.3
and 3GPP TS 25.123 subclause
9.1.1.1.3).

Values:

Summary of Contents for LE910C series

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for LE910C series

Reviews:

Brands by name

Popular brands

Telit Wireless Solutions LE910C series, At Commands Reference Manual

Search results

Summary of Contents for LE910C series

Reviews:

Brands by name

Popular brands