manualshive.com logo in svg

Telit Wireless Solutions LE910C series, At Commands Reference Manual

Share
Download
Page 438
Telit Wireless Solutions LE910C series At Commands Reference Manual Download Page 438

                

LE910Cx AT Commands Reference Guide

 

 

 
80502ST10950A Rev. 14 

Page 438 of 1904 

2022-03-04 

 

Not  Subject to NDA 

 

 

 

Full rate mode is added by default to any setting in the SETUP 
message (as specified in 3GPP TS 24.008), but the call drops if the 
network assigned codec mode has not been selected by the user. 

 

AT#CODEC=4 and AT#CODEC=16 are not recommended; better 
using AT#CODEC=5 and AT#CODEC=24 respectively 

 

The setting 0 is equivalent to the setting 255. 

 

  AT#CODEC? 

Read command returns current audio codec mode in the format: 

 

#CODEC: <codec> 

 

  AT#CODEC=? 

Test command returns the range of available values for parameter 
<codec> 

 

 

•

  AT#CODEC=14 

OK 

 

sets the codec modes HR (4), EFR (2) and AMR-FR (8) 

 

 

 

 

Summary of Contents for LE910C series

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands