Telit Wireless Solutions LE910C series At Commands Reference Manual Download Page 719

Page: 719 / 1904

Page 719

LE910Cx AT Commands Reference Guide

80502ST10950A Rev. 14

Page 719 of 1904

2022-03-04

Not Subject to NDA

3.8.4.

AT#WLANMODE - Change WLAN mode

This command is used to change the WLAN mode (AP/STA/AP+STA/AP+AP).

SIM Presence

Setting saved

Can be aborted

MAX timeout

SELINT

Not required

AT#WLANMODE=[<mode>]

Set command is used to change the WLAN mode
(AP/STA/AP+STA/AP+AP).

Parameter:

Name

Type

Default

Description

<mode>

integer

N/A

Status mode

Values:

0 : Access point mode

1 : STA mode

2 : AP+STA mode

3 : AP+AP mode

If #ETHMODE is set to 1 and ethernet is activated, this command
should not be set as STA mode or AP+STA mode.

AT#WLANMODE?

Read command returns the current mode status in the format:

#WLANMODE: <mode>

Where:

Summary of Contents for LE910C series

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for LE910C series

Reviews:

Brands by name

Popular brands

Telit Wireless Solutions LE910C series, At Commands Reference Manual

Search results

Summary of Contents for LE910C series

Reviews:

Brands by name

Popular brands