Telit Wireless Solutions LE910C series At Commands Reference Manual Download Page 348

Page: 348 / 1904

Page 348

LE910Cx AT Commands Reference Guide

80502ST10950A Rev. 14

Page 348 of 1904

2022-03-04

Not Subject to NDA

3.2.5.11.

AT#CALLDISA - Call Disable Setting

This command used to control the Disable Call Type and SMS only registration.

SIM Presence

Setting saved

Can be aborted

MAX timeout

SELINT

Not required

Auto

AT#CALLDISA=<disable_type>[,<sms_only>]

Set command sets the Disable Call Type and SMS only registration

Parameters:

Name

Type

Default

Description

<disable_type> integer

Disable Type. It is used to
enable/disable the Voice Call
function

Values:

0 : Enable Voice Call

1 : Disable Voice Call

2 : Disable Voice Call (same as 1)

<sms_only>

integer

SMS only. It is used to on/off the
SMS only parameter.

Values:

0 : None

1 : SMS only registration

Settings are affected after rebooting

If 1st parameter is set, the outgoing calls are not possible and the
incoming calls are rejected on the modem.

Summary of Contents for LE910C series

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for LE910C series

Reviews:

Brands by name

Popular brands

Telit Wireless Solutions LE910C series, At Commands Reference Manual

Search results

Summary of Contents for LE910C series

Reviews:

Brands by name

Popular brands