Telit Wireless Solutions LE910C series Page 223 At Commands Reference Manual Download

Page: 223 / 1904

Page 223

LE910Cx AT Commands Reference Guide

80502ST10950A Rev. 14

Page 223 of 1904

2022-03-04

Not Subject to NDA

3.2.2.66.

AT#FWSWITCH - Set Active Firmware Image

Set command allows enabling one configuration of the firmware configurations
embedded on product.

SIM Presence

Setting saved

Can be aborted

MAX timeout

SELINT

Not required

Auto

AT#FWSWITCH=<net_conf>[,<storage_conf>[,<restore_user_conf>]]

Set command allows enabling one configuration of the firmware
configurations embedded on product.

Parameters:

Name

Type

Default

Description

<net_conf>

integer

Network config to be enabled

Test command show the
supported <net_conf> values
range.

Please, refer to the table in
Additional info section where
is also described <net_conf>
list and the default values
depend on the products

<storage_conf>

integer

Selects storage configuration.
It's a dummy parameter for
the backward compatibility
with the legacy products.

Values:

0 : save the <configNumber> value in RAM

1 : save the <configNumber> value in NVM

Summary of Contents for LE910C series

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for LE910C series

Reviews:

Related manuals for LE910C series

Brands by name

Popular brands

Telit Wireless Solutions LE910C series, At Commands Reference Manual

Search results

Summary of Contents for LE910C series

Reviews:

Related manuals for LE910C series

Brands by name

Popular brands