Telit Wireless Solutions LE910C series Page 1089 At Commands Reference Manual Download | Manualshive

Page: 1089 / 1904

Page 1089

background image

LE910Cx AT Commands Reference Guide

80502ST10950A Rev. 14

Page 1089 of 1904

2022-03-04

Not Subject to NDA

The execution command #FASTSHDN<CR><LF> forces the module

to execute immediately fast power down regardless to the GPIO
status or enabled status.

All configured values stored on module and applied after next
power cycle.

However, LE910C1-EUX/SAX/SVX and LE910Cx-WWX can be
applied immediately.

The stored configuration is maintained when after firmware
switching.

It has highest priority than other functions when fast power down
enabled and GPIO is used as fast power down event monitoring.
Customer should not use GPIO for other function.

Execution command response can be omitted to reduce time
taking on power down.

Should do not use GPIO8 as fast power down pin on mPCIe type.

AT#FASTSHDN?

Read command returns the saved value in the format:

#FASTSHDN: <enable>,<pin>

AT#FASTSHDN=?

Test command reports the range for the parameters <enable> and <pin>.

«
...
1087
1088
1089
1090
1091
...
»

Summary of Contents for LE910C series

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LE910C series

Brand: Abocom Pages: 14

Brand: Icom Pages: 2

Brand: Ubiquiti Pages: 63

RailBox 11ac/WiFi 5

Brand: Acksys Pages: 36

Brand: Beats Electronics Pages: 8

Brand: Last Mile Gear Pages: 19

Brand: Aversky Technology Pages: 10

Brand: Technicolor Pages: 61

BLUESOCKET 3040

Brand: ADTRAN Pages: 6

BLUESOCKET 2135

Brand: ADTRAN Pages: 8

Brand: u-blox Pages: 64

Brand: Comcast Pages: 51

Brand: Redpine Signals Pages: 146

Brand: LogiLink Pages: 9

Brand: Ubiquiti Pages: 26

Brand: Intellinet Pages: 4

Brand: Intellinet Pages: 57

3CRWE20096A - Wireless LAN Access Point 2000

Brand: 3Com Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands