–
4
–
–
1
–
A-7168W-2EX-
q
Printed in Japan
© 2014–2015 Icom Inc.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
CONNECTION GUIDE
WIRELESS ACCESS POINT
AP-90M
Thank you for purchasing this Icom product. The AP-90M
wireless
access
point
is designed and built with Icom’s
IP network technology. It complies with the “IEEE802.11ac”
and “IEEE802.11n” standards, and is designed for dual
band communications in the 5 GHz and 2.4 GHz bands.
Read the “PRECAUTIONS” leaflet first, if you have not done so.
Supplied Accessories
D
• Cushion sheet
…………1
• Antenna
…………………2
• Mounting bracket set
…1
• Precautions guide
•
“Setting the interface language and the Time Zone” leaflet
• Connection Guide (This guide)
Other requirements
D
• PC
• Ground wire
• LAN cable
• Power adapter
( The adapter type differs, depending on the access point version)
About this Connection Guide:
This Connection Guide explains the basic operation of the
AP-90M. Access our website to download the instruction
manual.
Icom website http://www.icom.co.jp/world/
NOTE:
• Adobe
®
Reader
®
is required on your PC in order to display the
downloaded PDF instruction manual.
• If your PC does not have Adobe
®
Reader
®
, please download it
from the Adobe
®
website.
Step 1 System Requirements
Step 2 Panel description
About the indicators
D
*
1
When the LED OFF Mode is set to “Enable,” the light is dimmed, and when set to “Enable (Completely),” the light turns OFF. (Default: Disable)
*
2
When there is no wireless device to communicate with the AP-90M, or no wireless communication is performed while the Wireless Unit is
enabled, the LED lights orange. The time when the LED turns orange differs, depending on the communication status.
*
3
The LED also turns OFF when the same Wireless Mode is set to the internal antenna and the external antenna.
Step 6 Changing the administrator
’
s password
To prevent unauthorized access, you must change the password.
Enter
Click [Management], then [Administrator].
q
Fill out each box to change the password.
w
Click [Apply.]
e
* Enter the new administrator’s password from now on.
NOTE:
If you have forgotten your password, you cannot
access the AP-90M’s setting screen.
When you forgot your password:
Hold down the [MODE] button by following the instructions
described in the precautions guide. The AP-90M will have
to be reset as its default.
Click
LED
POWER*
1
LAN
WIRELESS 1
(Internal antenna)*
2
WIRELESS 2
(External antenna)*
2
Green
Lights
ON
LAN connected
(1000BASE-T)
More than 1 connection/WPS succeeded
Blinks
—
LAN is communicating (1000BASE-T)
WPS is running
Red
Lights
“Accessing the USB flash
drive” error
—
—
Blinks
“Duplicated IP address” error
—
WPS failed
Orange
Lights
Accessing the USB flash drive.
A firmware update is ready.
LAN connected
(10BASE-T/
100BASE-TX)
Internal antenna enabled
(Wireless unit is not connected)
External antenna enabled
(Wireless unit is not connected)
Blinks
Booting.
Operating [MODE].
LAN is communicating
(10BASE-T/
100BASE-TX)
Wireless operation is standing by for DFS
OFF
OFF
LAN is not connected
Internal antenna disabled*
3
External antenna disabled*
3
AP-90M
WIRELESS A
CCESS POINT
Antenna
connector
[LAN]
[POWER]
[WIRELESS 1]
[WIRELESS 2]
[
WPS
]
[LAN] port
(RJ-45)
[USB] port
(USB 2.0)
DC jack
Ground terminal
Antenna connector
Wi-Fi Protected Setup
[
MODE
]
Back side
[WIRELESS 1]: Internal antenna.
[WIRELESS 2*]: External antenna.
* The “IEEE802.11ac” standard can only be used when the 5
GHz band is selected.
Refer to “Resetting to the
factory defaults” in the Pre-
cautions Guide, for details.
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United
Kingdom, Germany, France, Spain, Russia and/or other countries.
Microsoft, Windows and Windows Server are registered trademarks of Microsoft Corporation in the United States and/or other
countries.
Adobe and Adobe Reader are registered trademarks of Adobe Systems Incorporated in the United States and/or other countries.
All other products or brands are registered trademarks or trademarks of their respective holders.
Step 7 DFS function and channel auto setting
The DFS function automatically avoids radio-frequency interference to Weather radars. The DFS conditions differ, depending on
your location.
NOTE
: Whether or not the DFS function is enabled on a frequency is regulated by the local law, and cannot be disabled by
users.
• The Wireless Bridging is not activated if a channel is used that requires the DFS function or if automatic channel selection is set.
Refer to the PDF instruction manual on the Icom’s website for setting details.
• The usable wireless LAN frequencies and channels differ, depending on your location.
After setting a channel in the setting screen, restart the
➥
AP-90M. The AP-90M will then search for a weather ra-
dar’s signal for approximately 1 minute.
While searching for a signal, [WIRELESS 1 or 2] will blink,
and access to the AP-90M will be paused.
When a weather radar’s signal is detected, the operating
channel automatically changes to a different channel to
avoid the interference.
The DFS function pauses on the new channel, if the chan-
➥
nel does not require the DFS.
