manualshive.com logo in svg

Telit Wireless Solutions LE910C series, At Commands Reference Manual

Share
Download
Page 1069
Telit Wireless Solutions LE910C series At Commands Reference Manual Download Page 1069

                

LE910Cx AT Commands Reference Guide

 

 

 
80502ST10950A Rev. 14 

Page 1069 of 1904 

2022-03-04 

 

Not  Subject to NDA 

 

3.13.5.

 

AT#MSDSEND - Sending MSD Data to IVS 

This command sends MSD data to IVS modem. 

 

SIM Presence 

Setting saved 

Can be aborted 

MAX timeout 

SELINT 

Not required 

Auto 

No 

- 

2 

 

  AT#MSDSEND 

Execution command allows to send 140 bytes of MSD data to the IVS 
embedded while modem is in command mode. 

 

The device responds to the command with the prompt 

'>' and waits for 

the MSD to send. 

To complete the operation, send Ctrl-Z char (0x1A hex); to exit without 
writing the message send ESC char (0x1B hex). 

 

If data are successfully sent, then the response is OK. 

If data sending fails for some reason, an error code is reported. 

 

The maximum number of bytes to send is 140; trying to send 
more data will cause the surplus to be discarded and lost. 

 

  AT#MSDSEND? 

Read command reports the stored MSD data, in the format: <stored MSD 
data> 

  AT#MSDSEND=? 

Test command returns the OK result code. 

 

 

Summary of Contents for LE910C series

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands