manualshive.com logo in svg

Telit Wireless Solutions LE910C series, At Commands Reference Manual

Share
Download
Page 655
Telit Wireless Solutions LE910C series At Commands Reference Manual Download Page 655

                

LE910Cx AT Commands Reference Guide

 

 

 
80502ST10950A Rev. 14 

Page 655 of 1904 

2022-03-04 

 

Not  Subject to NDA 

 

  If message is successfully sent to the network, then the result is 

sent in the format: 

+CMSS: <mr> 

 

Name 

Type 

Default 

Description 

<mr> 

integer 

- 

message reference number 

 

  If message sending fails for some reason, an error code is reported: 

+CMS ERROR:<err> 

 

 

 

To store a message in the <memw> storage see command +CMGW. 

 

Care must be taken to ensure that during the command execution, 
which may take several seconds, no other SIM interacting 
commands are issued. 

 

  AT+CMSS=? 

Test command returns the OK result code. 

 

 

To avoid malfunctions is suggested to wait for the +CMSS: <mr> or 
+CMS ERROR: <err> response before issuing further commands. 

 

 

Summary of Contents for LE910C series

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands