manualshive.com logo in svg

Telit Wireless Solutions LE910C series, At Commands Reference Manual

Share
Download
Page 1042
Telit Wireless Solutions LE910C series At Commands Reference Manual Download Page 1042

                

LE910Cx AT Commands Reference Guide

 

 

 
80502ST10950A Rev. 14 

Page 1042 of 1904 

2022-03-04 

 

Not  Subject to NDA 

 

Only <mode> 0 parameter is supported. 

AT#ACDB[=<mode>] 

Parameters: 

<mode> - Inject mode 

0 - Cold mode Injection. Audio Configuration is injected into FLASH. 

In order to be effective a reboot is required. 

 

After command line terminated with <CR>, We see the 
intermediate result code CONNECT. 

After this prompt, the file type must be in binary format. 

If data successfully sent, then the response is OK. 

If data sending fails for some reason, an error code reported. 

 

  AT#ACDB? 

LE910Cx Linux: 

Reports the supported range of <category> file. 

#ACDB: (0-1),(0-7),(File Size) 

 

LE910Cx ThreadX: 

Report OK 

OK 

 

Summary of Contents for LE910C series

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands