manualshive.com logo in svg

Teledyne HDO9000, Operator'S Manual

Share
Download
Teledyne HDO9000 Operator'S Manual Download Page 67

Acquisition

Replay Acquisition History

This is a good way to begin using History Mode. Watching a "movie" of the history allows you to see

waveform changes that are invisible during real-time acquisition.

Select

View History

to enable the display, then use the Navigation buttons or the slider bar at the

bottom of the dialog to "scroll" the history of acquisitions.

l

The top row buttons scroll: Fast Backward, Slow Backward, Slow Forward, Fast Forward.

l

The bottom row buttons step: Back to Start, Back One, Go to Index (row #), Forward One,

Forward to End.

Press Pause when you see something of interest, then use the History table to find the exact Index.

Select Single Acquisition

1. Select

View History

to enable the display, and

View Table

to show the index of records.

2. Optionally, select to show

Relative Times

on the table.

3. View individual acquisitions by selecting the row from the table or entering its

Index

number on

the dialog.

57

Summary of Contents for HDO9000





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands