Teledyne HDO9000 Operator'S Manual Download Page 22

Page: 22 / 188

HDO9000 High Definition Oscilloscopes Operator's Manual

Oscilloscope Set Up

Powering On/Off

Press the

Power button

to turn on the instrument. The X-Stream application loads automatically

when you use the Power button.

Caution:

Do not change the instrument’s Windows® Power Options setting from the default

Never to System Standby or System Hibernate. Doing so can cause the system to fail.

Caution:

Do not power on or calibrate with a signal attached.

Use the

File > Shutdown

menu bar option to switch "off". Pressing Power again will execute a

shutdown, but we do not recommend doing this because it does not allow the Windows operating

system to shut down properly, and memories and setup panels will not be saved. Never power off by

pulling the power cord from the socket or shutting off a connected power strip.

The Power button does not disconnect the instrument from the AC power supply. The only way to fully

power down the instrument is to unplug the AC power cord.
We recommend unplugging the instrument if it will remain unused for a long period of time.

Software Activation

The operating software (firmware and standard applications) is active upon delivery. At power-up, the

instrument loads the software automatically.

Firmware

Free firmware updates are available periodically from the Teledyne LeCroy website at:

teledynelecroy.com/support/softwaredownload

Registered users can receive an email notification when a new update is released. Follow the

instructions on the website to download and install the software.

Purchased Options

If you decide to purchase an option, you will receive a license key via email that activates the optional

features. See

Options

for instructions on activating optional software packages.

Summary of Contents for HDO9000





























































































































































































Search results

Summary of Contents for HDO9000

Reviews:

Brands by name

Popular brands

Teledyne HDO9000, Operator'S Manual

Search results

Summary of Contents for HDO9000

Reviews:

Brands by name

Popular brands