manualshive.com logo in svg

Teledyne HDO9000, Operator'S Manual

Share
Download
Teledyne HDO9000 Operator'S Manual Download Page 66

HDO9000 High Definition Oscilloscopes Operator's Manual

History Mode

History Mode allows you to review any acquisition saved in the history buffer, which automatically

stores all acquisition records until full. Not only can individual acquisitions be restored to the grid,

you can "scroll" backward and forward through the history at varying speeds to capture individual

details or changes in the waveforms over time.

Each record is indexed and time-stamped, and you can choose to view the absolute time of

acquisition or the time relative to when you entered History Mode. In the latter case, the last

acquisition is time zero, and all others are stamped with a negative time. The maximum number of

records stored depends on your acquisition settings and the total available memory.

Press the front panel

History Mode button

, or choose

Timebase > History Mode

to access this

feature.

Entering History Mode automatically stops new acquisitions. To leave History Mode, press the

History Mode button

again, or restart acquisition by pressing one of the front panel Trigger Mode

buttons.

Note:

History Mode does not work with Sequence Mode acquisitions, pre-processor

Interpolation set on the input channel, or channel interleaving.

Oscilloscope in History mode.

56

Summary of Contents for HDO9000





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands