manualshive.com logo in svg

Teledyne HDO9000, Operator'S Manual

Share
Download
Teledyne HDO9000 Operator'S Manual Download Page 171

Utilities

temperature when operating outside of the 19-30 °C range.

l

The instrument is moved to a new operating environment.

l

It has been six months since the previous manual calibration.

E-Mail

Use the E-mail dialog settings to configure e-mail on the instrument.

Under

E-Mail Server

, select the protocol used by your network:

l

MAPI

(Messaging Application Programming Interface) is the Microsoft interface specification

that allows different messaging and workgroup applications (including e-mail, voice mail, and

fax) to work through a single client, such as the Exchange client. MAPI uses the default

Windows e-mail application.

l

SMTP

(Simple Mail Transfer Protocol) is a TCP/IP protocol for sending messages from one

computer to another through a network. This protocol is used on the Internet to route e-mail. In

many cases no account is needed.

Under

Configuration

:

l

If you chose SMTP, touch

SMTP Server

and enter the network address of your mail server.

l

Touch

Originator Address (From:)

and enter the instrument's e-mail address.

l

Touch

Default Recipient Address (To:)

and enter the recipient's e-mail address.

Use

Send Test Mail

to send a confirmation message to ensure proper e-mail configuration.

161

Summary of Contents for HDO9000





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands