Teledyne HDO9000 Operator'S Manual Download Page 168

Page: 168 / 188

HDO9000 High Definition Oscilloscopes Operator's Manual

Preferences

Preference settings have mostly to do with the appearance and performance of the instrument itself,

rather than its interaction with other devices/systems.

To change LabNotebook application preferences, see

LabNotebook Preferences

Access the Preferences dialogs by choosing

Utilities > Preference Setup...

from the menu bar.

Audible Feedback

controls the instrument's audio output. Select this box to hear a beep each time

you touch a screen or front panel control.

Language

sets the language used on the touch screen display.

Font Size

changes the size of the text that appears on the touch screen display.

Performance

settings let you optimize performance for either

Analysis

(speed of acquisition and

calculation) or

Display

(speed of update/refresh). For example, if you are concerned with persistence

or averaging, you might optimize for Analysis, giving higher priority to waveform acquisition at the

expense of display update rate. Choices are presented as a spectrum.

There are also tabs linking to

, and

settings.

158

Summary of Contents for HDO9000





























































































































































































Search results

Summary of Contents for HDO9000

Reviews:

Brands by name

Popular brands

Teledyne HDO9000, Operator'S Manual

Search results

Summary of Contents for HDO9000

Reviews:

Brands by name

Popular brands