manualshive.com logo in svg

Teledyne HDO9000, Operator'S Manual

Share
Download
Teledyne HDO9000 Operator'S Manual Download Page 180

HDO9000 High Definition Oscilloscopes Operator's Manual

Canadian Certification

The instrument has been certified by Underwriters Laboratories (UL) to conform to the following

safety standard and bears cUL Listing Mark:

CAN/CSA-C22.2 No. 61010-1-12. Safety requirements for electrical equipment for measurement,

control and laboratory use.

Environmental Compliance

End-of-Life Handling

The instrument is marked with this symbol to indicate that it complies with the

applicable European Union requirements to Directives 2012/19/EU and 2013/56/EU on

Waste Electrical and Electronic Equipment (WEEE) and Batteries.

The product is subject to disposal and recycling regulations that vary by country and

region. Many countries prohibit the disposal of waste electronic equipment in standard

waste receptacles. For more information about proper disposal and recycling of your

Teledyne LeCroy product, please visit teledynelecroy.com/recycle.

Restriction of Hazardous Substances (RoHS)

This instrument and its accessories conform to the 2011/65/EU RoHS2 Directive.

ISO Certification

Manufactured under an ISO 9000 Registered Quality Management System.

170

Summary of Contents for HDO9000





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands