manualshive.com logo in svg

Teledyne HDO9000, Operator'S Manual

Share
Download
Teledyne HDO9000 Operator'S Manual Download Page 150

HDO9000 High Definition Oscilloscopes Operator's Manual

Customize Reports

The Advanced dialog allows you to customize the LabNotebook report creation function.

Change Directories

To change where Notebooks are stored, change the

Notebooks Directory

folder.

To change where reports are output, change the

Report Directory

folder. You can choose an external

location, such as a USB drive.

Change Report Template

Deselect

Use Default

next to the Template field, then touch

Browse

and select a different template

from the D:\Xport folder.

You can create your own report template and place it in this directory for selection. Templates must

be saved as .xsl or .xslt files.

Change Logo

The included LabNotebook report templates use our logo as a placeholder. You can replace this with

your custom logo. Logo files should be in bitmap (.bmp) format and not exceed 100 pixels high by 180

pixels wide.

1. Copy the logo file to the D:\Xport folder.

2. Choose

File > LabNotebook

, then touch the

Advanced

tab.

3. Deselect the

Use Default

checkbox next to the Logo field.

4. Touch the

Browse

button and navigate to the the new logo file. Select and touch

OK

.The new

file path appears in the Logo field with a preview of the image above it.

140

Summary of Contents for HDO9000





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands