Teledyne HDO9000 Operator'S Manual Download Page 181

Page: 181 / 188

Certifications

Warranty

THE WARRANTY BELOW REPLACES ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,

INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS, OR

ADEQUACY FOR ANY PARTICULAR PURPOSE OR USE. TELEDYNE LECROY SHALL NOT BE LIABLE

FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER IN CONTRACT OR

OTHERWISE. THE CUSTOMER IS RESPONSIBLE FOR THE TRANSPORTATION AND INSURANCE

CHARGES FOR THE RETURN OF PRODUCTS TO THE SERVICE FACILITY. TELEDYNE LECROY WILL

RETURN ALL PRODUCTS UNDER WARRANTY WITH TRANSPORT PREPAID.

The product is warranted for normal use and operation, within specifications, for a period of three

years from shipment. Teledyne LeCroy will either repair or, at our option, replace any product returned

to one of our authorized service centers within this period. However, in order to do this we must first

examine the product and find that it is defective due to workmanship or materials and not due to

misuse, neglect, accident, or abnormal conditions or operation.

The instrument’s firmware has been thoroughly tested and is presumed to be functional.

Nevertheless, it is supplied without warranty of any kind covering detailed performance.

Teledyne LeCroy shall not be responsible for any defect, damage, or failure caused by any of the

following: a) attempted repairs or installations by personnel other than Teledyne LeCroy

representatives or b) improper connection to incompatible equipment, or c) for any damage or

malfunction caused by the use of non-Teledyne LeCroy supplies. Furthermore, Teledyne LeCroy shall

not be obligated to service a product that has been modified or integrated where the modification or

integration increases the task duration or difficulty of servicing the instrument. Spare and

replacement parts, and repairs, all have a 90-day warranty.

Products not made by Teledyne LeCroy are covered solely by the warranty of the original equipment

manufacturer.

Intellectual Property

All patents pertaining to the HDO9000 can be found on our website at:

teledynelecroy.com/patents/

Windows License Agreement

The oscilloscope application software runs on a Windows® operating system. Teledyne LeCroy's

agreement with Microsoft® prohibits users from installing third-party software that is not relevant to

measuring, analyzing, or documenting waveforms.

171

Summary of Contents for HDO9000





























































































































































































Search results

Summary of Contents for HDO9000

Reviews:

Brands by name

Popular brands

Teledyne HDO9000, Operator'S Manual

Search results

Summary of Contents for HDO9000

Reviews:

Brands by name

Popular brands