manualshive.com logo in svg

Teledyne HDO9000, Operator'S Manual

Share
Download
Teledyne HDO9000 Operator'S Manual Download Page 43

Using MAUI

traces, pinching will alter the acquisition timebase and the scale of all traces. Create a

separate zoom trace if you do not wish to do this.

All zoom traces open in the next empty grid, with the zoomed portion of the source trace highlighted.

If there are no more available grids, zooms will open in the same grid as the source trace.

Zoomed area of original trace highlighted. Zoom in new grid below.

Quick Zoom

Use the

front panel Zoom button

to quickly create one zoom trace for each displayed channel trace.

Quick zooms are created at the same vertical scale as the source trace and 10:1 horizontal

magnification.

To turn off the quick zooms, press the Zoom button again.

Manually Create Zoom

To manually create a zoom, touch-and-drag diagonally to draw a selection box around any part of the

source trace.

Selection box over trace.

The zoom will resize the selected area to fit the full width of the grid. The degree of vertical and

horizontal magnification, therefore, depends on the size of the rectangle that you draw.

33

Summary of Contents for HDO9000





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands