Sun Microsystems Sun SPARC Enterprise M3000 User Manual Download Page 232

Page: 232 / 398

4-12

SPARC Enterprise Mx000 Servers XSCF User’s Guide • August 2009

■

showpowerupdelay

■

setshutdowndelay

■

showshutdowndelay

■

setdualpowerfeed

■

showdualpowerfeed

With the power operations, the following can be performed:

■

System power on

■

System power off

■

Domain power on

■

Domain power off

■

Sending a Domain Panic Request (Solaris OS dump request)

■

Domain reset

■

Sending break signal to a domain

■

Air-conditioning wait time administration

■

Warm-up time administration

■

Dual power feed

4.4.1

System Power On

■

Command operation

1. Use the

showdomainstatus

(8) command to check the power status of the

system.

2. Use the

poweron

(8) command to turn on power to all domains.

XSCF>

showdomainstatus -a

DID

Domain Status

Running

Powered Off

Summary of Contents for Sun SPARC Enterprise M3000















































































































































































































































































































































































































Search results

Summary of Contents for Sun SPARC Enterprise M3000

Reviews:

Related manuals for Sun SPARC Enterprise M3000

Brands by name

Popular brands

Sun Microsystems Sun SPARC Enterprise M3000, User Manual

Search results

Summary of Contents for Sun SPARC Enterprise M3000

Reviews:

Related manuals for Sun SPARC Enterprise M3000

Brands by name

Popular brands