Sun Microsystems Sun SPARC Enterprise M3000 User Manual Download Page 223 | Manualshive

Page: 223 / 398

background image

Chapter 4

Operation of the Server

4-3

4. Use the

showstatus

(8) command to display information on degraded

components in the system.

(This screenshot is provided as an example.)

5. Use the

showenvironment

(8) command to display the ambient temperature,

humidity, and voltage of the system.

(This screenshot is provided as an example.)

Note –

The humidity information is only displayed in M8000/M9000 servers.

Environmental Temperature and Fan Speed Level

With the altitude setting, the fan speed level varies by the environmental
temperature. To display the fan speed for each environmental temperature, execute
the

showenvironment

(8) command. Fan speed level indicates Low speed, Middle

speed, or High speed.

XSCF>

showstatus

* BP_A Status:Degraded;

* DDC_A#0 Status:Faulted;

* PSU#0 Status:Faulted;

XSCF>

showenvironment

Temperature:30.70C

Humidity:90.00%

XSCF>

showenvironment temp

Temperature:30.70C

CMU#0:43.00C

CPUM#0-CHIP#0:65.00C

CPUM#1-CHIP#0:61.20C

CPUM#2-CHIP#0:64.80C

CPUM#3-CHIP#0:63.60C

CMU#1:45.50C

:

XSCF>

showenvironment volt

MBU_B

1.0V Power Supply Group:1.000V

1.8V Power Supply Group:1.910V

CPUM#0-CHIP#0

1.0V Power Supply Group:1.050V

:

«
...
221
222
223
224
225
...
»

Summary of Contents for Sun SPARC Enterprise M3000















































































































































































































































































































































































































Reviews:

No comments

Related manuals for Sun SPARC Enterprise M3000

Express5800/320Ma

Brand: NEC Pages: 80

Express5800/320Ma

Brand: NEC Pages: 90

Brand: Sun Fire Pages: 66

Brand: Synology Pages: 15

FusionServer 2288 V5

Brand: xFusion Digital Technologies Pages: 86

Brand: AIC Pages: 79

Brand: TRENDnet Pages: 135

PowerEdge R6415

Brand: Dell EMC Pages: 139

TourMaster MLA2504

Brand: Coachsound Pages: 22

Brand: Maverick System Pages: 58

Brand: seneye Pages: 11

easyRAID FN-420GT

Brand: easyRAID NAS Pages: 128

SuperCluster T5-8

Brand: Oracle Pages: 356

Brand: Dell EMC Pages: 149

Brand: Gateway Pages: 96

DiskStation DS213

Brand: Synology Pages: 21

PS111W - Print Server - Parallel

Brand: NETGEAR Pages: 21

PS111W - Print Server - Parallel

Brand: NETGEAR Pages: 106

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands