Sun Microsystems Sun SPARC Enterprise M3000 User Manual Download Page 200

Page: 200 / 398

2-148

SPARC Enterprise Mx000 Servers XSCF User’s Guide • August 2009

6. Turn the input power supply of the server off, then on.

Note –

For more about encrypted data, see the man page or the

XSCF Reference

Manual

of the

restoreconfig

(8) command.

Restoring the Configuration Information from a Specified Target
Directory Over a Network

■

Command operation

1. Power off all domains.

2. Perform the

restoreconfig

(8) command specifying the target directory.

3. When the data transfer is complete, confirm the identification data in the head

of the saved configuration file.

4. The XSCF will be reseted. After the data is restored, the XSCF will be halted.

Turn the input power supply of the server off, then on.

Note –

For more about encrypted data, see the man page or the

XSCF Reference

Manual

of the

restoreconfig

(8) command.

XSCF> restoreconfig ftp://server/backup/backup-sca-ff2-16.txt

Summary of Contents for Sun SPARC Enterprise M3000















































































































































































































































































































































































































Search results

Summary of Contents for Sun SPARC Enterprise M3000

Reviews:

Related manuals for Sun SPARC Enterprise M3000

Brands by name

Popular brands

Sun Microsystems Sun SPARC Enterprise M3000, User Manual

Search results

Summary of Contents for Sun SPARC Enterprise M3000

Reviews:

Related manuals for Sun SPARC Enterprise M3000

Brands by name

Popular brands