Sun Microsystems Sun SPARC Enterprise M3000 User Manual Download Page 207

Page: 207 / 398

Chapter 3

Connecting to the XSCF and the Server

3-7

1. Confirm that a serial cable is inserted into the serial connector on the front of

the XSCF Unit, and confirm that the PC and workstation to be used are
correctly connected.

2. Check whether the following are set on the terminal software.

Baud rate: 9600 bps, Data length: 8 bit, No parity, STOP bit: 1 bit,

No flow control, Delay: Except for 0

Summary of Contents for Sun SPARC Enterprise M3000















































































































































































































































































































































































































Search results

Summary of Contents for Sun SPARC Enterprise M3000

Reviews:

Related manuals for Sun SPARC Enterprise M3000

Brands by name

Popular brands

Sun Microsystems Sun SPARC Enterprise M3000, User Manual

Search results

Summary of Contents for Sun SPARC Enterprise M3000

Reviews:

Related manuals for Sun SPARC Enterprise M3000

Brands by name

Popular brands