Sun Microsystems Sun SPARC Enterprise M3000 User Manual Download Page 255

Page: 255 / 398

Chapter 5

Overview of the XSCF Shell

5-3

ping

Checks the response for a host.

traceroute

Displays the network path to the host by list.

settimezone

Specifies the time zone.

showtimezone

Displays the time zone setting.

setdate

Sets the XSCF time.

showdate

Displays the XSCF time.

setntp

Configures the NTP server.

showntp

Displays the SSH settings and fingerprint.

resetdateoffset

Resets the time subtraction between the XSCF and the domain.

showdateoffset

Displays the time subtraction between the XSCF and the domain.

setssh

Configures SSH. Generates RSA and DSA keys for SSH2 host authentication.

showssh

Displays the SSH settings and fingerprint.

settelnet

Configures telnet.

showtelnet

Displays the telnet settings.

setautologout

Sets the session timeout time of the XSCF Shell.

showautologout

Displays the session timeout time of the XSCF Shell.

setsmtp

Configures the SMTP server.

showsmtp

Displays the the SMTP server settings.

setemailreport

Configures mail notification.

showemailreport

Displays the mail notification settings.

setlookup

Enables or disables the use of an LDAP server for authentication and user privilege
lookup.

showlookup

Displays information about whether an LDAP server is used for authentication and
user privilege lookup.

setldap

Configures LDAP client settings.

showldap

Displays LDAP client settings.

sethttps

Configures the https settings.

showhttps

Displays the https settings.

TABLE 5-1

XSCF Commands

(Continued)

Command

Description

Summary of Contents for Sun SPARC Enterprise M3000















































































































































































































































































































































































































Search results

Summary of Contents for Sun SPARC Enterprise M3000

Reviews:

Related manuals for Sun SPARC Enterprise M3000

Brands by name

Popular brands

Sun Microsystems Sun SPARC Enterprise M3000, User Manual

Search results

Summary of Contents for Sun SPARC Enterprise M3000

Reviews:

Related manuals for Sun SPARC Enterprise M3000

Brands by name

Popular brands