Sun Microsystems Sun SPARC Enterprise M3000 User Manual Download Page 231

Page: 231 / 398

Chapter 4

Operation of the Server

4-11

Note –

In the M3000 server, the domain configuration policy can be changed by

using the

setdcl

(8) command. However, other domain configurations cannot be

changed.

Commands Used to Setup or Display Information

Execute the following commands individually, as appropriate. For details of these
commands, see

Chapter 5

■

setdcl

■

setupfru

■

addboard

■

deleteboard

■

moveboard

For details on adding or changing a domain, see

Chapter 2

of the

XSCF Reference

Manual

or the

Administration Guide

For details on using the DR function to change the domain configuration, see the

Dynamic Reconfiguration User’s Guide

4.4

Server and Domain Power Operations

This section describes power operations for servers and domains, and it explains
how to display the power status of a server or domain.

To perform the power operations, use the XSCF Shell commands.

Commands Used for the Operations or Status Display

Execute the following commands individually, as appropriate. For details of these
commands, see

Chapter 5

■

poweron

■

poweroff

■

reset

■

sendbreak

■

setpowerupdelay

Summary of Contents for Sun SPARC Enterprise M3000















































































































































































































































































































































































































Search results

Summary of Contents for Sun SPARC Enterprise M3000

Reviews:

Related manuals for Sun SPARC Enterprise M3000

Brands by name

Popular brands

Sun Microsystems Sun SPARC Enterprise M3000, User Manual

Search results

Summary of Contents for Sun SPARC Enterprise M3000

Reviews:

Related manuals for Sun SPARC Enterprise M3000

Brands by name

Popular brands