manualshive.com logo in svg

Sun Microsystems Sun SPARC Enterprise M3000, User Manual

The Sun SPARC Enterprise M3000 is a high-performance server by Sun Microsystems. Providing exceptional computing power, this user-friendly product offers a wide range of capabilities. Unlock the full potential of your device with our detailed and comprehensive user manual, available for free download at our website.

Share
Download
background image

8-26

SPARC Enterprise Mx000 Servers XSCF User’s Guide • August 2009

2. When the data transfer is complete, please contact authorized service

personnel.

Note –

For detail of

snapshot

(8) command, including how to enable encryption,

see the man page or the

XSCF Reference Manual

.

Caution –

IMPORTANT

- When the XSCF Unit is the redundant configuration, log

in to the standby side and collect the log in the same way.

The form of the collected log file is as follows.

XSCF>

snapshot -t [email protected]:/home/joe/logs/x

:

File name :

The file name is generated automatically at XSCF IP address and the
log taking out time. So, the log file cannot be generated in the file name
of the user specification.

File format :

zip

Summary of Contents for Sun SPARC Enterprise M3000















































































































































































































































































































































































































Reviews:

No comments

Related manuals for Sun SPARC Enterprise M3000

U.S. Converters XS1000 User Manual preview
XS1000
Brand: U.S. Converters Pages: 5
IBM eServer 342 xSeries Installation Manual preview
eServer 342 xSeries
Brand: IBM Pages: 70
IEI Technology AVL-2000PLUS User Manual preview
AVL-2000PLUS
Brand: IEI Technology Pages: 34
Kathrein SAT-IP EXIP 418 User Manual preview
SAT-IP EXIP 418
Brand: Kathrein Pages: 16
Acrosser Technology ANR-C62-N1 Series Manual preview
ANR-C62-N1 Series
Brand: Acrosser Technology Pages: 57
Fujitsu PRIMEQUEST 440 System Design Manual preview
PRIMEQUEST 440
Brand: Fujitsu Pages: 280
SEH IC125-FASTPOCKET-FX Installation Manual preview
IC125-FASTPOCKET-FX
Brand: SEH Pages: 20
SEH myUTN-52 Quick Installation Manual preview
myUTN-52
Brand: SEH Pages: 32
XtendLan TC-40xL User Manual preview
TC-40xL
Brand: XtendLan Pages: 50
Gigabyte G221-Z30 User Manual preview
G221-Z30
Brand: Gigabyte Pages: 143
Multitech ProxyServer MTPSR3-100 User Manual preview
ProxyServer MTPSR3-100
Brand: Multitech Pages: 79
Meinberg LANTIME M300 Technical Reference preview
LANTIME M300
Brand: Meinberg Pages: 41
Planet Networking & Communication ICS-2200T User Manual preview
ICS-2200T
Brand: Planet Networking & Communication Pages: 67
Planet Networking & Communication ICS-2100T User Manual preview
ICS-2100T
Brand: Planet Networking & Communication Pages: 76
Z Microsystems ZX2 User Manual preview
ZX2
Brand: Z Microsystems Pages: 21
Dell EMC PowerEdge R7515 Installation And Service Manual preview
PowerEdge R7515
Brand: Dell EMC Pages: 169
Dell EMC E68S Installation And Service Manual preview
E68S
Brand: Dell EMC Pages: 187
NASdeluxe NDL-2700T+ Installation Manual preview
NDL-2700T+
Brand: NASdeluxe Pages: 6

Brands by name

Popular brands

Load more brands