Sun Microsystems Sun SPARC Enterprise M3000 User Manual Download Page 78

Page: 78 / 398

2-26

SPARC Enterprise Mx000 Servers XSCF User’s Guide • August 2009

Note –

All DSCP addresses must be in the same network subnet.

Specifying a Host Name for XSCF

■

Command operation

1. Use the

showhostname

(8) command to display host names.

2. Use the

sethostname

(8) command to specify a host name.

XSCF>

showhostname -a

xscf#0: scf-hostname0.company.com

xscf#1: scf-hostname1.company.com

<Example 1> Specify the host name scf0-hostname for XSCFU#0.

XSCF>

sethostname xscf#0 scf0-hostname

<Example 2> Specify the domain name com for XSCFU#0.

XSCF>

sethostname -d company.com

Summary of Contents for Sun SPARC Enterprise M3000















































































































































































































































































































































































































Search results

Summary of Contents for Sun SPARC Enterprise M3000

Reviews:

Related manuals for Sun SPARC Enterprise M3000

Brands by name

Popular brands

Sun Microsystems Sun SPARC Enterprise M3000, User Manual

Search results

Summary of Contents for Sun SPARC Enterprise M3000

Reviews:

Related manuals for Sun SPARC Enterprise M3000

Brands by name

Popular brands