Sun Microsystems Sun SPARC Enterprise M3000 User Manual Download Page 42 | Manualshive

Page: 42 / 398

background image

1-16

SPARC Enterprise Mx000 Servers XSCF User’s Guide • August 2009

The following connections in the XSCF Unit connection configuration shown in

FIGURE 1-4

are described below:

■

Serial port connection

■

XSCF-LAN Ethernet connection

Serial Port Connection

The serial port enables workstations, PCs, and ASCII terminals to connect to the
XSCF through the serial (RS-232C) port. The user can use the XSCF Shell and access
the domain console through the XSCF Shell.

XSCF-LAN Ethernet Connection

XSCF-LAN Ethernet enables workstations and PCs to connect to the XSCF through
the XSCF-LAN port. The following can be used with XSCF-LAN Ethernet:

■

XSCF Shell via a SSH or telnet connection

■

XSCF Web from a web browser running on the terminal

■

Domain console access

■

Mail reports

■

SNMP notification

For details on these XSCF functions, see the following chapters:

■

Settings for each function:

Chapter 2

■

Shell terminal and console connections:

Chapter 3

■

XSCF Shell:

Chapter 5

■

XSCF mail functions:

Chapter 6

■

XSCF SNMP Agent functions:

Chapter 7

■

XSCF Web:

Chapter 9

1.3.1

Examples of LAN Connection Operations

The XSCF Unit has two 10/100 Mbps XSCF-LAN two ports.

TABLE 1-2

to

TABLE 1-4

outlines three XSCF-LAN operation examples.

«
...
40
41
42
43
44
...
»

Summary of Contents for Sun SPARC Enterprise M3000















































































































































































































































































































































































































Reviews:

No comments

Related manuals for Sun SPARC Enterprise M3000

ShareCenter DNS-343

Brand: D-Link Pages: 12

Brand: D-Link Pages: 38

Epress EtherNetwork DP-301P+

Brand: D-Link Pages: 2

Brand: Patton electronics Pages: 326

Brand: Inspur Pages: 82

SUPERO SuperServer 1018L-MP

Brand: Supermicro Pages: 104

UniServer T1100 G3

Brand: H3C Pages: 138

SUPERSERVER 5017C-MF

Brand: Supero Pages: 96

BladeCenter HS20 Type 8843

Brand: IBM Pages: 112

Brand: QNAP Pages: 68

Brand: BRONKHORST Pages: 19

Brand: disguise Pages: 12

Brand: Cisco Pages: 2

RuggedJet RJ-4040

Brand: Brother Pages: 111

Brand: Brother Pages: 253

Maxtor Central Axis

Brand: Maxtor Pages: 2

Brand: Leightronix Pages: 22

Brand: IBM Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands