Sun Microsystems Sun SPARC Enterprise M3000 User Manual Download Page 184

Page: 184 / 398

2-132

SPARC Enterprise Mx000 Servers XSCF User’s Guide • August 2009

3. Use the

showdomainmode

(8) command to confirm the initial hardware

diagnostic level.

Enabling or Disabling the Host Watchdog Function and the Break Signal
Suppression

■

Command operation

1. Use the

showdomainmode

(8) command to display the host watchdog and break

signal suppression setting.

2. Use the

setdomainmode

(8) command to specify host watchdog and break

signal suppression.

<Example> Specify the maximum initial hardware diagnostic level for domain ID 0.

XSCF>

setdomainmode -d 0 -m diag=max

Diagnostic Level :min -> max

Secure Mode

:off

-> -

Autoboot

:on

-> -

CPU Mode

:auto

-> -

The specified modes will be changed.

Continue? [y|n]:

configured.

Diagnostic Level :max

Secure Mode

:off (host watchdog: unavailable Break-signal:receive)

Autoboot

:on (autoboot:on)

CPU Mode

:auto

<Example> Display the initial hardware diagnostic levels of domain

ID 0.

XSCF>

showdomainmode -d 0

Host-ID

:0f010f10

Diagnostic Level :max

Secure Mode :off

Autoboot

:on

CPU Mode

:auto

<Example> Display the setting for domain ID 0.

XSCF>

showdomainmode -d 0

Host-ID

:0f010f10

Diagnostic Level :max

Secure Mode :off

Autoboot

:on

CPU Mode

:auto

Summary of Contents for Sun SPARC Enterprise M3000















































































































































































































































































































































































































Search results

Summary of Contents for Sun SPARC Enterprise M3000

Reviews:

Related manuals for Sun SPARC Enterprise M3000

Brands by name

Popular brands

Sun Microsystems Sun SPARC Enterprise M3000, User Manual

Search results

Summary of Contents for Sun SPARC Enterprise M3000

Reviews:

Related manuals for Sun SPARC Enterprise M3000

Brands by name

Popular brands