Sun Microsystems Sun SPARC Enterprise M3000 User Manual Download Page 167

Page: 167 / 398

Chapter 2

Setting Up XSCF

2-115

3. Use the

addboard

(8) command to add an XSB and use the

showboards

(8)

command to confirm the XSB status.

4. Use the

poweron

(8) command to start up domain ID 2.

5. Use the

console

(8) command to connect a domain console. Check the

configuration by using

prtdiag

(1M).

To switch from the domain console to the XSCF Shell, press the Enter, “#” (default
escape character), and “.” (period) keys.

6. Use the

showboards

(8) command to confirm the XSB status. (See

TABLE 2-23

<Example> Assign XSB#00-0, XSB#01-0, XSB#01-1, XSB#01-2, XSB#01-3 to domain ID

XSCF>

addboard -c assign -d 2 00-0 01-0 01-1 01-2 01-3

XSB#00-0 will be assigned to DomainID 2. Continue?[y|n] :

XSB#01-0 will be assigned to DomainID 2. Continue?[y|n] :

XSB#01-1 will be assigned to DomainID 2. Continue?[y|n] :

XSB#01-2 will be assigned to DomainID 2. Continue?[y|n] :

XSB#01-3 will be assigned to DomainID 2. Continue?[y|n] :

XSCF>

showboards -va

XSB R DID(LSB) Assignment

Pwr

Conn Conf Test

Fault

COD

---- - -------- ----------- ---- ---- ---- ------- -------- ----

00-0

02(00)

Assigned

Passed

Normal

01-0

02(07)

Assigned

Passed

Normal

01-1

02(08)

Assigned

Passed

Normal

01-2

02(09)

Assigned

Passed

Normal

01-3

02(10)

Assigned

Passed

Normal

XSCF>

poweron –d 2

DomainIDs to power on:02

Continue? [y|n] :

02 :Powering on

*Note*

This command only issues the instruction to power-on.

The result of the instruction can be checked by the "showlogs

power".

<Example> Connect the OS console of domain ID 2.

XSCF>

console –d 2

Connect to DomainID 2?[y|n] :

exit from console.

Summary of Contents for Sun SPARC Enterprise M3000















































































































































































































































































































































































































Search results

Summary of Contents for Sun SPARC Enterprise M3000

Reviews:

Related manuals for Sun SPARC Enterprise M3000

Brands by name

Popular brands

Sun Microsystems Sun SPARC Enterprise M3000, User Manual

Search results

Summary of Contents for Sun SPARC Enterprise M3000

Reviews:

Related manuals for Sun SPARC Enterprise M3000

Brands by name

Popular brands