Sun Microsystems Sun SPARC Enterprise M3000 User Manual Download Page 80

Page: 80 / 398

2-28

SPARC Enterprise Mx000 Servers XSCF User’s Guide • August 2009

2. Use the

setroute

(8) command to specify the routing environment for a

network interface.

Making XSCF DNS Settings

■

Command operation

1. Use the

shownameserver

(8) command to display the name server. If multiple

name servers are added, they are displayed on separate lines.

2. Use the

setnameserver

(8) command to specify the name server.

<Example 1> Add routing with Destination 192.168.1.0 and Netmask

255.255.255.0 to XSCF-LAN#0 in the XSCFU#0.

XSCF>

setroute -c add -n 192.168.1.0 -m 255.255.255.0 xscf#0-lan#0

<Example 2> Add routing with the default network for Destination

and Gateway 10.12.108.1 to XSCF-LAN#1 in the XSCFU#0.

XSCF>

setroute -c add -n 0.0.0.0 -g 10.12.108.1 xscf#0-lan#1

<Example 3> Delete routing with destination 192.168.1.0 and netmask

255.255.255.0 to XSCF-LAN#0 in the XSCFU#0.

XSCF>

setroute -c del -n 192.168.1.0 -m 255.255.255.0 xscf#0-lan#0

<Example 1> Confirm that three name servers are added.

XSCF>

shownameserver

nameserver 10.0.0.2

nameserver 172.16.0.2

nameserver 192.168.0.2

<Example 2> Confirm that no name server is added.

XSCF>

shownameserver

---

<Example 1> Add the three IP addresses 10.0.0.2, 172.16.0.2, and

192.168.0.2 as name servers.

XSCF>

setnameserver 10.0.0.2 172.16.0.2 192.168.0.2

<Example 2> Delete all available name servers.

XSCF>

setnameserver -c del -a

Summary of Contents for Sun SPARC Enterprise M3000















































































































































































































































































































































































































Search results

Summary of Contents for Sun SPARC Enterprise M3000

Reviews:

Related manuals for Sun SPARC Enterprise M3000

Brands by name

Popular brands

Sun Microsystems Sun SPARC Enterprise M3000, User Manual

Search results

Summary of Contents for Sun SPARC Enterprise M3000

Reviews:

Related manuals for Sun SPARC Enterprise M3000

Brands by name

Popular brands