Sun Microsystems Sun SPARC Enterprise M3000 User Manual Download Page 254

Page: 254 / 398

5-2

SPARC Enterprise Mx000 Servers XSCF User’s Guide • August 2009

■

auditop: The user can refer to the audit method of the XSCF and the audit
records.

■

auditadm: The user can control the audit to the XSCF.

■

fieldeng: The user can perform the commands for FEs.

TABLE 5-1

outlines the XSCF Shell commands. For details on each command and user

privileges, see the man page or the

XSCF Reference Manual

TABLE 5-1

XSCF Commands

Command

Description

adduser

Creates an XSCF user account.

deleteuser

Deletes an XSCF user account.

disableuser

Disables an XSCF user account

enableuser

Enables an XSCF user account.

showuser

Displays XSCF user account information. Alternatively, it displays the user's own
user account information.

password

Changes an XSCF user account password. Alternatively, it changes the user's own
XSCF user account password.

setpasswordpolicy

Configures the XSCF password policy.

showpasswordpolicy

Displays the XSCF password policy.

setprivileges

Assigns user privileges.

setloginlockout

Configures the lockout of user accounts.

showloginlockout

Displays the lockout setting of user accounts.

setnetwork

Configures the XSCF network.

shownetwork

Displays the XSCF network settings and XSCF-LAN network status.

setroute

Configures the XSCF-LAN route.

showroute

Displays XSCF-LAN route settings.

sethostname

Specifies the XSCF-LAN host name and domain name.

showhostname

Displays the XSCF-LAN host name and domain name.

setnameserver

Sets a name server (DNS) with XSCF.

shownameserver

Displays the XSCF name server(s).

applynetwork

Applies the network settings.

setdscp

Configures DSCP.

showdscp

Displays the DSCP settings.

nslookup

Checks for the name resolution of a host name.

Summary of Contents for Sun SPARC Enterprise M3000















































































































































































































































































































































































































Search results

Summary of Contents for Sun SPARC Enterprise M3000

Reviews:

Related manuals for Sun SPARC Enterprise M3000

Brands by name

Popular brands

Sun Microsystems Sun SPARC Enterprise M3000, User Manual

Search results

Summary of Contents for Sun SPARC Enterprise M3000

Reviews:

Related manuals for Sun SPARC Enterprise M3000

Brands by name

Popular brands