Sun Microsystems Sun SPARC Enterprise M3000 User Manual Download Page 234

Page: 234 / 398

4-14

SPARC Enterprise Mx000 Servers XSCF User’s Guide • August 2009

Note –

Only the domains that are able to be powered off are displayed.

Note –

If the

poweroff

(8) command is performed, and the shutdown has

completed, then the domain is powered off.

4.4.3

Domain Power On

■

Command operation

1. Use the

showdomainstatus

(8) command to check the power status of all

domains.

XSCF>

poweroff -a

DomainIDs to power off:00,01,02,03

Continue? [y|n] :

00 : Powering off

01 : Powering off

02 : Powering off

03 : Powering off

*Note*

This command only issues the instruction to power-off.

The result of the instruction can be checked by the

"showlogs power".

XSCF>

showdomainstatus -a

DID

Domain Status

Powered Off

Running

Powered Off

Summary of Contents for Sun SPARC Enterprise M3000















































































































































































































































































































































































































Search results

Summary of Contents for Sun SPARC Enterprise M3000

Reviews:

Related manuals for Sun SPARC Enterprise M3000

Brands by name

Popular brands

Sun Microsystems Sun SPARC Enterprise M3000, User Manual

Search results

Summary of Contents for Sun SPARC Enterprise M3000

Reviews:

Related manuals for Sun SPARC Enterprise M3000

Brands by name

Popular brands