Sun Microsystems Sun SPARC Enterprise M3000 User Manual Download Page 123

Page: 123 / 398

Chapter 2

Setting Up XSCF

2-71

Enabling or Disabling Audit, Transferring a Log File, and Deleting
Audit Data

■

Command operation

1. Use the

showaudit

(8) command to display audit settings.

2. Use the

setaudit

(8) command to configure auditing.

<Example> Display all information on the current audit status in

the system.

XSCF>

showaudit all

Auditing:

enabled

Audit space used:

13713 (bytes)

Audit space free:

4180591 (bytes)

Records dropped:

Policy on full trail: count

User global policy:

enabled

Mail:

Thresholds:

80% 100%

User policy:

Events:

AEV_AUDIT_START

enabled

AEV_AUDIT_STOP enabled

<Example 1> Disable writing to the audit trail and transfer the log

file.

XSCF>

setaudit disable

<Example 2> Enable writing to the audit trail.

XSCF>

setaudit enable

Turns on writing of the audit records for the audit trail.

< Example 3> Request the log file transfer.

XSCF>

setaudit archive

< Example 4> Delete the log data of the audit trail.

XSCF>

setaudit delete

Summary of Contents for Sun SPARC Enterprise M3000















































































































































































































































































































































































































Search results

Summary of Contents for Sun SPARC Enterprise M3000

Reviews:

Related manuals for Sun SPARC Enterprise M3000

Brands by name

Popular brands

Sun Microsystems Sun SPARC Enterprise M3000, User Manual

Search results

Summary of Contents for Sun SPARC Enterprise M3000

Reviews:

Related manuals for Sun SPARC Enterprise M3000

Brands by name

Popular brands