manualshive.com logo in svg

Sun Microsystems Sun SPARC Enterprise M3000, User Manual

The Sun SPARC Enterprise M3000 is a high-performance server by Sun Microsystems. Providing exceptional computing power, this user-friendly product offers a wide range of capabilities. Unlock the full potential of your device with our detailed and comprehensive user manual, available for free download at our website.

Share
Download
background image

Chapter 2

Setting Up XSCF

2-139

TABLE 2-33

lists the settings and the corresponding shell commands.

Note –

After the drive units are used for a domain (even if domain configuration is

changed and CPU/Memory Board unit or the I/O unit is replaced) the settings of
the IOUA port number are valid.

TABLE 2-33

DVD Drive/Tape Drive Unit Configuration

Item

Description

Shell Command

Remarks

Display DVD
drive/tape
drive unit
setting
information

Displays the DVD drive/tape drive unit setting
information for an IOUA port.

cfgdevice

DVD
drive/tape
drive unit

Sets the target IOUA port for connecting or
disconnecting DVD drive and tape drive units.
(Note)
Specify the following:
• Connect/disconnect
• IOUA port number (I/O unit number - IOUA

number)
I/O unit number: 0-7; basic cabinet

8-15; expansion cabinet

cfgdevice

In the system with
expansion cabinet,
the IOUA port
number is
specified one per
cabinet.

Summary of Contents for Sun SPARC Enterprise M3000















































































































































































































































































































































































































Reviews:

No comments

Related manuals for Sun SPARC Enterprise M3000

D-Link ShareCenter DNS-343 Quick Install Manual preview
ShareCenter DNS-343
Brand: D-Link Pages: 12
Cabletron Systems MicroMMAC 22ES Installation Manual preview
MicroMMAC 22ES
Brand: Cabletron Systems Pages: 93
PaloAlto Networks M-100 Hardware Reference Manual preview
M-100
Brand: PaloAlto Networks Pages: 30
IBM Netfinity 1000-8477 21Y Hardware Maintenance Manual preview
Netfinity 1000-8477 21Y
Brand: IBM Pages: 268
Supermicro SuperServer 1029P-MT User Manual preview
SuperServer 1029P-MT
Brand: Supermicro Pages: 123
HIKVISION DS-6101HFI-IP User Manual preview
DS-6101HFI-IP
Brand: HIKVISION Pages: 31
RIOT CloudLink Installation Manual preview
CloudLink
Brand: RIOT Pages: 18
Acer Aspire EASYSTORE H341 Quick Start Manual preview
Aspire EASYSTORE H341
Brand: Acer Pages: 59
Acer Aspire EASYSTORE H341 Service Manual preview
Aspire EASYSTORE H341
Brand: Acer Pages: 74
Acer Aspire EasyStore Series User Manual preview
Aspire EasyStore Series
Brand: Acer Pages: 148
Acer Aspire easyStore H340 Service Manual preview
Aspire easyStore H340
Brand: Acer Pages: 68
Acer Altos EasyStore User Manual preview
Altos EasyStore
Brand: Acer Pages: 169
Acer Aspire easyStore H340 User Manual preview
Aspire easyStore H340
Brand: Acer Pages: 148
Acer Altos EasyStore Quick Installation Manual preview
Altos EasyStore
Brand: Acer Pages: 7
Dell PowerEdge 400SC Update preview
PowerEdge 400SC
Brand: Dell Pages: 1
D-Link DPR-1260 - RangeBooster G Multifunction Print Server User Manual preview
DPR-1260 - RangeBooster G Multifunction Print Server
Brand: D-Link Pages: 55
D-Link DPR-1061 Quick Installation Manual preview
DPR-1061
Brand: D-Link Pages: 49
LG 27CN650N Owner'S Manual preview
27CN650N
Brand: LG Pages: 100

Brands by name

Popular brands

Load more brands