Sony LMT-300, User Manual

Page: 35 / 71

28
Projector
C
h
ap
te
r 1
U
s
e
r Gu
id
e
FUNCTIONs (F1 through F20). The majority of the
projector settings must be configured and saved to a
FUNCTION using the SRX Controller
1
application.
However, some settings may require adjustment of a more
immediate nature. These are available to you on the
FUNCTION SETUP screen.
Note: Controls in the ADJUST PROJECTOR group are
unavailable when the Projection Type is set to “Single
3D”.
A limited number of
adjustments are available
on the FUNCTION
SET-UP pane. To access
Function Setups, tap
Menu, tap Projector and
then tap Function Setup .
The FUNCTION
SET-UP pane appears.
Caution: Any changes
made to adjustments on
the FUNCTION SET-UP
pane change the
presentation as soon as
the adjustment is made.
However, unless “Saved” prior to leaving the
FUNCTION SETUP screen the changes will not be
present the next time the same FUNCTION is selected.
Changes which are
Saved to the FUNCTION will be
reflected in the settings returned the next time the indicated
FUNCTION is selected on the Projector Control panel or
recalled when an SPL includes a CPL associated with the
FUNCTION.
From the FUNCTION SETUP screen you can set LAMP
POWER and adjust image related settings (ADJUST
PROJECTOR). The settings are stored for later recall
using the indicated FUNCTION (Current Function).
Configure Function
From the FUNCTION SET-UP pane you adjust selected
functions and can save the changed values to the Current
Function (refer to
“Change Projector Function” on page
26 ).
Verify Current/Target Function
MAKE SURE THAT THE CORRECT (TARGET)
FUNCTION, e.g., F2 WB-6500, APPEARS IN “
Current
Function ” BEFORE MAKING ANY ADJUSTMENT ON
THIS SCREEN.
Once changes are saved to the Current Function THERE
IS NO “UNDO” and the changes you have made will
affect the presentation every time the FUNCTION is
recalled using either the Projector control screen or when
the FUNCTION is associated with a CPL as part of a Show
or SPL.
To change the Current Function refer to “Change
Projector Function” on page 26 . The Current Function
indicates the FUNCTION selected either manually or by
CPL to FUNCTION association.
Note: When a FUNCTION is selected on the
PROJECTOR CONTROL pane it may take some seconds
to complete the process as some adjustments are
mechanical in nature, e.g., Zoom, Focus, etc. During this
time the auditorium screen may be dark.
If you make changes to settings and prior to saving the
changes exit the FUNCTION SET-UP screen the changes
will be discarded. However, the changed settings on the
projector remain until a new FUCNTION is selected.
Note: While adjustments will immediately affect the
projector operation they are temporary and, unless Saved,
will be lost when another FUNCTION is selected.
Adjust Lamp Power
Screen Luminance vs. Lamp Power
The SRX-R320 based system includes a Lamp Control
Mode
2
which can manage the screen luminance by directly
measuring the brightness of the bulb using a photocell.
During the system installation the Lamp Brightness, and
therefore Screen Luminance, is calibrated against Lamp
Power. This is realized by stepping the Lamp Power from
its minimum value (50) to its maximum value (100),
measuring the bulb brightness vs. the Lamp Power, and
then storing this data in a table in the projector. A
1.The SRX Controller exercises direct control over the
projector and therefore should not be used at the same time
the Projectionist Terminal or SMS Controller is in opera-
tion.
Tap Function Setup
Projector Menu
2.The Lamp Control Mode is set on the INSTALLATION
screen of the SRX Controller application. This functions is
disabled when the Lamp Power option is used, under
which the Lamp Power value is saved to the FUNCTION
instead of the photocell measured brightness. When the
FUNCTION is recalled, the actual lamp power will be set
to the saved value. In this case, Calibrate Luminance oper-
ation is not required.
Save to FUNCTION
Current Function