SOMFY Animeo 1870452 Manual Download | Manualshive

Page: 8 / 56

background image

animeo KNX 4 DC Motor Controller

28.02.2019

WM 24 V DC



2019 Somfy Activités SA



Ref. 5147817A

8/56

4 Settings in the delivery state

The Motor Controller KNX can be used in the delivery state also without prior programming by the ETS soft-
ware. Practical presets are implemented in the device. These settings apply to all four motor outputs.

•

Move times UP/DOWN, CLOSED/OPEN = 5 minutes

•

Connection of local conventional push buttons is possible

The local push button inputs are assigned directly to the motor outputs: Push button input 1 controls motor
output 1 (fig. 1). The motor outputs can be controlled through bridging the wire at the push button inputs
when required (fig. 2).

4.1 Function of the Reset/Prog button

H

The basic settings in the KNX Motor Controller can be made using this push button. These basic settings

are possible only in the delivery state, before the device with the ETS was programmed, or after the device
was unassigned by the ETS.
The basic settings are overwritten by the settings in the ETS.

«
...
6
7
8
9
10
...
»

Summary of Contents for Animeo 1870452

























































Reviews:

No comments

Related manuals for Animeo 1870452

Brand: Baby Trend Pages: 24

Brand: Baby Trend Pages: 6

Brand: Baby Trend Pages: 6

Brand: C3 Custom Coolers Pages: 16

Brand: Walimex Pro Pages: 68

Brand: Mamas & Papas Pages: 24

Brand: Mamas & Papas Pages: 24

Brand: Radionics Pages: 14

Brand: V2 Pages: 12

Brand: H3C Pages: 5

NORA-W10 Series

Brand: u-blox Pages: 56

Brand: z21 Pages: 2

Brand: Tylo Pages: 51

MicroTech II UV05

Brand: AAF Pages: 50

Brand: S&C Pages: 26

Brand: Radionics Pages: 18

Brand: Renogy Pages: 36

Brand: Yoshitake Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands