SOMFY Animeo 1870452 Manual Download Page 37

Page: 37 / 56

animeo KNX 4 DC Motor Controller

28.02.2019

WM 24 V DC



2019 Somfy Activités SA



Ref. 5147817A

37/56

6.8.7 Dimming Brighter/Darker

Default value:



Adjust by

Selection options:



Adjust by 100%



Adjust by ½



Adjust by ¼



Adjust by



Adjust by



Adjust by



Adjust by

This parameter defines the dimming length of steps of the telegrams which are transmitted with a longer
pressing.

When

“Dimming with cyclic intervals” is parameterized, attention must be paid to the fact that the dimming

length of steps and the interval for the cyclical dimming are matched to the dimming time of the actuator.

6.8.8 Interval for cyclic dimming

Default value:



0.5 seconds

Selection options:



0.5 - 7.0 seconds

This

parameter defines the duration of an interval for cyclical sending. If, for example, a “change ¼” and an

“interval of 0.5 seconds” is set, then with a longer pressing of the push button on the corresponding local in-
put, every 0.5 seconds ¼ brighter or darker will be dimmed.

Summary of Contents for Animeo 1870452
























































Search results

Summary of Contents for Animeo 1870452

Reviews:

Brands by name

Popular brands

SOMFY Animeo 1870452, Manual

Search results

Summary of Contents for Animeo 1870452

Reviews:

Brands by name

Popular brands