manualshive.com logo in svg

SOMFY Animeo 1870452, Manual

Share
Download
SOMFY Animeo 1870452 Manual Download Page 53

 

animeo KNX 4 DC Motor Controller 

28.02.2019 

 

WM 24 V DC 

 
 

 2019 Somfy Activités SA 

 Ref. 5147817A 

53/56 

6.19 Menu 

index card “Radio inputs – Venetian blind slow tilting” 

 

 

 

6.19.1 Basic Function  

Selected option: 

  Venetian blind slow tilting 

 

6.19.2 Long operation (action) after 

 
This parameter defines the pressing time of the corresponding transmitter push button (Up/Down) which 
makes a distinction between the sending of a short-term telegram (Up/Down) and a long-term telegram 
(Open/Close). If the time, for example, is set at 0.5 seconds, a longterm telegram is generated after a longer 
pressing than 0.5 seconds. With a pressing duration which is shorter than 0.5 seconds, a shortterm telegram 
is generated. 

6.19.3 Tilt slats slowly Open/Close 

 
This parameter defines the turn of the Venetian blinds which is transmitted as a telegram with a long press-
ing of the push button. 
 

6.19.4 Functionality of my push button 

Default value: 

  No function 

Selection options: 

  1-Bit value 

 

  8-Bit value 

 

  No function 

 

6.19.4.1 

1-Bit value 

Default value: 

  On 

Selection options: 

  On 

 

  Off 

 

  Toggle 

 

 

  No function 

 

 

Summary of Contents for Animeo 1870452

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands