manualshive.com logo in svg

SOMFY Animeo 1870452, Manual

Share
Download
SOMFY Animeo 1870452 Manual Download Page 9

 

animeo KNX 4 DC Motor Controller 

28.02.2019 

 

WM 24 V DC 

 
 

 2019 Somfy Activités SA 

 Ref. 5147817A 

9/56 

4.2  Selection of different user ergonomics 

Using the Reset/Prog button the press button user ergonomics for the local push button inputs or Somfy RTS 
radio hand transmitter can be determined. These settings are possible only in the delivery state, before the 
device is programmed with ETS software or after the device is unassigned with the ETS. 
As soon as the device with the ETS is programmed, no further settings of the user ergonomics can be made 
via the Reset/Prog button. When the device is unassigned by the ETS, the adjusting of the user ergonomics 
is possible again via the Reset/Prog button. 

H

 The selection of the user ergonomics must match with a corresponding end product. 

 

 

= 

Learning-in of animeo RTS radio module 

SCR 

= 

Screen ergonomics*  

EU 

= 

Venetian blind, EU ergonomics*  

US 

= 

Venetian blind, US ergonomics*  

 
*see chapter 1 

“Definitions” 

 

 
 

4.3  Changing the ergonomics 

 

 

 
 
 
 
 
 

 

To change to different ergonomics 
press briefly the Reset/Prog button. 
Repeat till such time as the desired 
LED shines. 

The delivery state is Venetian Blind 
with EU ergonomics 

Save and 
exit the 
setting mode 

Summary of Contents for Animeo 1870452

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands