SOMFY Animeo 1870452 Manual Download Page 32

Page: 32 / 56

animeo KNX 4 DC Motor Controller

28.02.2019

WM 24 V DC



2019 Somfy Activités SA



Ref. 5147817A

32/56

6.6

Menu index card “Binary inputs – Switch/Dry contact”

6.6.1 Basic Function

Selected option:



Switch dry contact

6.6.2 Edge evaluation contact A

Default value:



Rising On, falling Off

Selection options:



Rising On, falling Off



Rising Off, falling On



Rising On



Falling On



Rising Off



Falling Off



Rising toggle



Falling toggle



Rising toggle, falling toggle



No evaluation

See chapter 1 Definitions

for On (“1”) Off (“0”) Toggle (“1/0”).

The corresponding object value “0” or “1” is generated depending on which edge evaluation is parameter-
ized.

•

Rising On, falling Off

If a rising

edge at the local input appears, the object value “On” is generated. If a falling edge at the local in-

put appears, the object value “Off” is generated. The duration of the activation is not evaluated.

•

Rising Off, falling On

If a rising flank at the local

input appears, the object value “Off” is generated. If a falling flank at the local in-

put appears, the object value “On” is generated. The duration of the activation is not evaluated.

•

Rising On

If a rising flank at the local input appears, the object val

ue “On” is generated. If a falling flank at the local in-

put appears, it is not evaluated. The duration of the activation is not evaluated.

•

Falling On

If a rising flank at the local input appears, the object value “On” is generated. If a rising flank at the local input
appears, it is not evaluated. The duration of the activation is not evaluated.

Summary of Contents for Animeo 1870452
























































Search results

Summary of Contents for Animeo 1870452

Reviews:

Brands by name

Popular brands

SOMFY Animeo 1870452, Manual

Search results

Summary of Contents for Animeo 1870452

Reviews:

Brands by name

Popular brands