manualshive.com logo in svg

SOMFY Animeo 1870452, Manual

Share
Download
SOMFY Animeo 1870452 Manual Download Page 22

 

animeo KNX 4 DC Motor Controller 

28.02.2019 

 

WM 24 V DC 

 
 

 2019 Somfy Activités SA 

 Ref. 5147817A 

22/56 

6  Parameter 

The selection options of the single parameters are described in each case. The defaults are printed in italics. 
In the following illustrations of the different parameter cards the maximum number of parameters is shown. 
Besides this and depending on the parameter settings, objects which are not required are hidden. 

6.1  Menu index card 

“General” 

 

 

 

6.1.1  Standard settings of the motors 

Default value: 

  Combined 

Selection options: 

  Combined 

 

  Individual 

 
With these parameters the settings of the 

motor outputs are made as to whether “Combined” or “Individual”. 

With the parameter “Combined” only one menu index card becomes visible for the basic settings of all four 
motor outputs (motor 1-4). 

H

 

The selection „Combined“ is recommended for projects for which the settings of the motor outputs are the 

same. 
With the 

parameter „Individual“ four single cards become visible for the standard settings of the motor out-

puts (motor 1, motor 2, …). 

6.1.2  Select priority Automatic/Manual 

Default value: 

  No 

Selection options: 

  No 

 

  Yes 

 
With the parameter 

“Yes” the settings for the priority functions become visible. At the same time the neces-

sary objects appear. 
 

 

Summary of Contents for Animeo 1870452

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands