SOMFY Animeo 1870452 Manual Download | Manualshive

Page: 51 / 56

background image

animeo KNX 4 DC Motor Controller

28.02.2019

WM 24 V DC



2019 Somfy Activités SA



Ref. 5147817A

51/56

6.18

Menu index card “Radio inputs – Dimming”

6.18.1 Basic Function

Selected option:



Dimming

6.18.2 Long operation (action) after

Default value:



0.5 seconds

Selection options:





0.3...5.0 seconds

This parameter defines the pressing time of the corresponding transmitter push button (Up/Down) which
makes a distinction between the sending of a short-term telegram (On/Off) and a long-term telegram
(Brighter/darker dimming). If the time, for example, is set at 0.5 seconds, a long-term telegram is generated
after a longer pressing than 0.5 seconds. With a pressing duration which is shorter than 0.5 seconds, a
short-term telegram is generated.

6.18.3 Dimming Brighter/Darker

Default value:



Adjust by

⅛

Selection options:



Adjust by 100 %

1

/

16

This parameter defines the dimming step length which is transmitted as a telegram with a long pressing of
the push button.

6.18.4 Functionality of my push button

Default value:



No function

Selection options:



1-Bit value



8-Bit value



No function

«
...
49
50
51
52
53
...
»

Summary of Contents for Animeo 1870452

























































Reviews:

No comments

Related manuals for Animeo 1870452

Brand: zipwake Pages: 12

Brand: Watts Pages: 2

Brand: jbc Pages: 12

Brand: Farris Engineering Pages: 12

Brand: Eastern Times Technology Pages: 4

Brand: Vacon Pages: 18

Brand: Canarm Pages: 3

Brand: Valor Pages: 20

iBox Hub 25020180

Brand: Hans Grohe Pages: 36

Brand: Eaton Pages: 2

PXI-6683 Series

Brand: National Instruments Pages: 4

Brand: National Instruments Pages: 9

Brand: National Instruments Pages: 11

Brand: National Instruments Pages: 29

Brand: National Instruments Pages: 11

Brand: National Instruments Pages: 7

FIELDPOINT FP-1600

Brand: National Instruments Pages: 21

FieldPoint FP-1001

Brand: National Instruments Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands