manualshive.com logo in svg

SOMFY Animeo 1870452, Manual

Share
Download
SOMFY Animeo 1870452 Manual Download Page 41

 

animeo KNX 4 DC Motor Controller 

28.02.2019 

 

WM 24 V DC 

 
 

 2019 Somfy Activités SA 

 Ref. 5147817A 

41/56 

6.11.2 Reaction at main power return (24 V) (for all motors) 

Default value: 

  Ignore 

Selection options: 

  Upper end limit  

 

  Lower end limit  

 

  Ignore 

 

  Close window  

 

  Open window 

 
This parameter defines the position which is moved to with a mains power return (24 V). 
 

6.11.3 Automatic cascading 

Default value: 

  No 

Selection options: 

  No 

 

  Yes 

 
If this parameter is set on “Yes”, the motor outputs with one second delay in each case move to the corre-
sponding position. This delay time is taken into account with the start-up of the positions, which are gener-
ated from the settings “Reaction with bus voltage return” and “Reaction with mains voltage return (24 V)”.  

H

 Advantage: Power spikes can thus be reduced in larger projects. 

 

 

Summary of Contents for Animeo 1870452

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands