SOMFY Animeo 1870452 Manual Download | Manualshive

Page: 10 / 56

background image

animeo KNX 4 DC Motor Controller

28.02.2019

WM 24 V DC



2019 Somfy Activités SA



Ref. 5147817A

10/56

4.4 Manual learning-in of move times

The move and turn times per motor output can be set via local conventional push buttons. These settings are
possible only in the delivery state before the device has been programmed with the ETS. As soon as the de-
vice with the ETS is programmed, the move times and turn times can no longer be set via local conventional
push buttons. When the device is unassigned by the ETS, the adjusting of the move times and turn times via
local conventional push buttons can be done again.

H

Alternatively to the conventional push buttons, the settings can also be done using the Somfy RTS Trans-

mitter and animeo RTS Radio Module (ref. 1860105). A setting using animeo KNX RTS Receiver (ref.
1860191) and Somfy RTS Transmitter resp. animeo EnOcean Receiver (ref. 1860220) or animeo KNX
EnOcean Receiver (ref. 1860229) und EnOcean Receiver is not possible!

4.5 Manual learning-in of the intermediate position 1

Intermediate position 1 can be learned-in individually per motor output via conventional local push buttons. At
the same time, it is possible to carry out the intermediate position 1 via settings in the ETS parameters. Prior
to this, the move and turn times must be learned-in!

H

Alternatively to the conventional push buttons, the settings can also be done using the Somfy RTS Trans-

mitter and animeo RTS Radio Module (ref. 1860105). A setting using animeo KNX RTS Receiver (ref.
1860191) and Somfy RTS Transmitter resp. animeo EnOcean Receiver (ref. 1860220) or animeo KNX
EnOcean Receiver (ref. 1860229) and EnOcean Sender is possible through using the objects 64-67!

4.5.1 Save intermediate position 1 (IP1)

«
...
8
9
10
11
12
...
»

Summary of Contents for Animeo 1870452

























































Reviews:

No comments

Related manuals for Animeo 1870452

Brand: J4C Pages: 4

Brand: ABB Pages: 6

Brand: Eaton Pages: 166

Brand: Samson Pages: 36

Brand: FBII Pages: 71

Brand: CAME Pages: 4

Brand: Acclaim Lighting Pages: 32

Brand: Jeep Pages: 19

Brand: Vasco Pages: 32

Brand: Abra Pages: 16

Brand: SAI Pages: 16

Brand: Hable Pages: 3

Brand: Bang & Olufsen Pages: 36

Brand: Mad Catz Pages: 4

ROBO Cylinder RCP2 Series

Brand: IAI Pages: 5

SIGMA CONTROL 2

Brand: KAESER KOMPRESSOREN Pages: 246

Brand: Vacon Pages: 50

Brand: V2 Pages: 116

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands