SOMFY Animeo 1870452 Manual Download | Manualshive

Page: 43 / 56

background image

animeo KNX 4 DC Motor Controller

28.02.2019

WM 24 V DC



2019 Somfy Activités SA



Ref. 5147817A

43/56

•

Up/Down position

Using this parameter the position Up/Down is sent on the bus for the corresponding motor depending on the
parameter “Type of messaging” “0” = upper/”255” = lower.

•

Slat position

With this parameter the slat position is transmitted for the corresponding motor depending on the parameter
“Type of messaging” on the bus. “0/255” = slats opened/”255/0” = slats closed. The value for the position of
the slats which is transmitted over the corresponding object is dependent on the parameter settings on the
menu index card “General”.
Slats turn Closed/Turned ONLY WITH VENETIAN BLIND.

•

Up/Down and slat position

With this parameter the position Up/Down and the position of the slats for the corresponding motor is trans-
mitted on the bus depending on the parameter “Type of messaging”. “0” = upper/”255” = lower, “0/255” =
slats opened/”255/0” = slats closed. The value for the position of the slats which is transmitted over the cor-
responding object is dependent on the parameter settings on the menu index card

“General”.

Slats turn Closed/Turned ONLY WITH VENETIAN BLIND.

•

None

No positions on the bus are messaged.

6.12.4

Motor 1…4 Type of feedback

Default value:



On demand

Selection options:



On demand



Status change



Cyclic

•

On demand

The current position of the blinds must be requested over object 50.

•

Status change

The current position of the corresponding blind is transmitted after every position change on the bus. The
position is transmitted on the bus when the destination position is reached.

•

Cyclic

This parameter opens a further parameter (“Every”) with which the time for cyclical sending is set.

6.12.5 Every

Default value:



5 seconds

Selection options:



5 seconds



10 seconds



20 seconds



30 seconds



60 seconds

H

With this parameter it is defined in which time intervals the current position of the corresponding blinds

are messaged. The current position of the blinds is transmitted on the bus.

«
...
41
42
43
44
45
...
»

Summary of Contents for Animeo 1870452

























































Reviews:

No comments

Related manuals for Animeo 1870452

Brand: ABATEC Pages: 8

Brand: M&C Pages: 16

GRAVIMETRIC AUGER FEEDER MGF-ST

Brand: Maguire Products Pages: 47

Brand: Magtrol Pages: 160

Brand: Velleman Pages: 26

Brand: Velleman Pages: 32

Brand: Velocity Pages: 84

Brand: Lab.gruppen Pages: 2

TruPortal TP-ADD-1DIP

Brand: Interlogix Pages: 9

KOOL STRIDE KS-S

Brand: KOOL-STOP Pages: 8

Brand: Nemesis Pages: 6

Brand: Watlow Pages: 20

Brand: Vertiv Pages: 2

Brand: Quantum Pages: 20

Brand: Veichi Electric Pages: 8

Brand: olympia electronics Pages: 22

Brand: Kelly Pages: 37

Brand: Watts Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands