manualshive.com logo in svg

SOMFY Animeo 1870452, Manual

Share
Download
SOMFY Animeo 1870452 Manual Download Page 30

 

animeo KNX 4 DC Motor Controller 

28.02.2019 

 

WM 24 V DC 

 
 

 2019 Somfy Activités SA 

 Ref. 5147817A 

30/56 

6.3.6  Block Step/Stop orders (1 Bit) 

Default value: 

  No 

Selection options: 

  No 

 

  Yes 

 
Step/stop and turn commands (bit) can be blocked per object (51-54) using this parameter. If a telegram with 
the value 

“1” is received on the corresponding object during a blinds turn, this turn is carried out up to the 

end. Only then further turn commands (bit) are blocked. If a telegram with the value 

“0” is received on the 

corresponding object, the step/stop or turn commands (bit) are released again. 
 

6.3.7  Block local push button inputs and Somfy RTS orders 

Default value: 

  No 

Selection options: 

  No 

 

  Yes 

 
Local push buttons inputs and the Somfy RTS radio signal can be blocked per object (51-54) using this 
parameter. If a telegram with the value 

“1” is received on the corresponding object during a motor movement, 

this turn is carried out up to the end. Only after completion any further commands are blocked which are gen-
erated via local push button inputs or Somfy RTS radio signals. If a telegram with the value 

“0” is received on 

the corresponding object, the local push button inputs and Somfy RTS radio signals are freed again. 

H

 This function is deactivated for local push-button inputs if "Yes" has been selected in the "Use universal 

binary inputs" menu index card (see section 6.1.4). 
 

6.3.8  Repeat last telegram after security 

Default value: 

  No 

Selection options: 

  No 

 

  Yes 

 
If this parameter is set to 

“Yes”, the last move command is repeated after security. This means that it will 

move to the position which was active before a telegram with the value 

“1” was input to one of the corre-

sponding security objects, low or high. 

6.4  General information for Binary inputs 

 
Four different basis functions can be selected for each universal input: 
 
Default value: 

  Venetian blind, Up/Down 

Selection options: 

  Venetian blind, Up/Down  

 

  Switch dry contact 

 

  8-Bit value (rising edge) 

 

  Dimming 

 
The single functions and parameters will be explained which arise depending on the selection of the basis 
function. For this, another basis function has been selected for each push button. The functions are de-
scribed with the help of the input 1 contact A/B and are identical for the inputs 2-4, contacts C/D, E/F and 
G/H. 

H

 

For the basis function “Venetian blind Up/Down “ attention must be paid to which contact “Up” or “Down” 

is switched. The same applies with selection basis function “Dimming”, for “Brighter” or “Darker” dimming. 
The pre-

setting of the basis function for the menu index card push button 1…4 is Venetian blind Up/Down. 

 

 

Summary of Contents for Animeo 1870452

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands