Siemens Synco living Operating Instructions Manual Download Page 88

Page: 88 / 100

88 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Service

23.08.2008

Display after battery change

After insertion of the new batteries,
the full display appears for 2 sec-
onds. Then, the room unit changes to
Normal operation.

The room operating mode settings are interrogated by the central
apartment unit. Any active room timer function will not be reactivated.

After inserting the new batteries, the battery capacity is checked at the room
temperature sensor QAA910 and the meteo sensor QAC910 . During the
check, the green LED lights up for 2 seconds, provided the batteries have
sufficient capacity.

After the battery check, the devices directly switch to Normal operation. The
LED will extinguish again.

Radiator control actuator SSA955

Have 3 new Alkaline AA batteries
ready for insertion (LR6 / 1.5 V).

Press on the snap-on cover…

2707Z22

2707Z23

… and remove the battery compart-
ment cover.

Remove the old batteries.

2707Z25

2707Z26

Summary of Contents for Synco living





































































































Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands

Siemens Synco living, Operating Instructions Manual

Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands